Zabbix Documentation 3.4

2.23.03.4In development:4.0Unsupported versions:1.82.02.43.2

User Tools

Site Tools


manual:appendix:config:zabbix_agentd_win

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
manual:appendix:config:zabbix_agentd_win [2018/02/08 06:45]
martins-v adding a default for 'LogFile'
manual:appendix:config:zabbix_agentd_win [2018/06/14 05:53] (current)
martins-v Server is mandatory, unless StartAgents=0
Line 25: Line 25:
 | PerfCounter| no | | |Syntax: <​parameter_name>,"<​perf_counter_path>",<​period>​\\ Defines new parameter <​parameter_name>​ which is an average value for system performance counter <​perf_counter_path>​ for the specified time period <​period>​ (in seconds).\\ For example, if you wish to receive average number of processor interrupts per second for last minute, you can define new parameter "​interrupts"​ as following:​\\ PerfCounter = interrupts,"​\Processor(0)\Interrupts/​sec",​60\\ Please note double quotes around performance counter path.\\ The parameter name (interrupts) is to be used as the item key when creating an item.\\ Samples for calculating average value will be taken every second.\\ You may run "​typeperf -qx" to get list of all performance counters available in Windows. | | PerfCounter| no | | |Syntax: <​parameter_name>,"<​perf_counter_path>",<​period>​\\ Defines new parameter <​parameter_name>​ which is an average value for system performance counter <​perf_counter_path>​ for the specified time period <​period>​ (in seconds).\\ For example, if you wish to receive average number of processor interrupts per second for last minute, you can define new parameter "​interrupts"​ as following:​\\ PerfCounter = interrupts,"​\Processor(0)\Interrupts/​sec",​60\\ Please note double quotes around performance counter path.\\ The parameter name (interrupts) is to be used as the item key when creating an item.\\ Samples for calculating average value will be taken every second.\\ You may run "​typeperf -qx" to get list of all performance counters available in Windows. |
 | RefreshActiveChecks| no | 60-3600 |120 |How often list of active checks is refreshed, in seconds.\\ Note that after failing to refresh active checks the next refresh will be attempted after 60 seconds. | | RefreshActiveChecks| no | 60-3600 |120 |How often list of active checks is refreshed, in seconds.\\ Note that after failing to refresh active checks the next refresh will be attempted after 60 seconds. |
-| Server| yes, if StartAgents is not 0; no otherwise ​| | |List of comma delimited IP addresses, optionally in CIDR notation, or hostnames of Zabbix servers.\\ Incoming connections will be accepted only from the hosts listed here.\\ If IPv6 support is enabled then '​127.0.0.1',​ '::​127.0.0.1',​ '::​ffff:​127.0.0.1'​ are treated equally and '::/​0'​ will allow any IPv4 or IPv6 address.\\ '​0.0.0.0/​0'​ can be used to allow any IPv4 address.\\ Note, that "​IPv4-compatible IPv6 addresses"​ (0000::/96 prefix) are supported but deprecated by [[https://​tools.ietf.org/​html/​rfc4291#​section-2.5.5|RFC4291]].\\ Example: Server=127.0.0.1,​192.168.1.0/​24,::​1,​2001:​db8::/​32,​zabbix.domain\\ Spaces are allowed since the Zabbix 2.2 version. |+| Server| yes, if StartAgents is not explicitly set to 0 | | |List of comma delimited IP addresses, optionally in CIDR notation, or hostnames of Zabbix servers.\\ Incoming connections will be accepted only from the hosts listed here.\\ If IPv6 support is enabled then '​127.0.0.1',​ '::​127.0.0.1',​ '::​ffff:​127.0.0.1'​ are treated equally and '::/​0'​ will allow any IPv4 or IPv6 address.\\ '​0.0.0.0/​0'​ can be used to allow any IPv4 address.\\ Note, that "​IPv4-compatible IPv6 addresses"​ (0000::/96 prefix) are supported but deprecated by [[https://​tools.ietf.org/​html/​rfc4291#​section-2.5.5|RFC4291]].\\ Example: Server=127.0.0.1,​192.168.1.0/​24,::​1,​2001:​db8::/​32,​zabbix.domain\\ Spaces are allowed since the Zabbix 2.2 version. |
 | ServerActive| no | (*) | |IP:port (or hostname:​port) of Zabbix server or Zabbix proxy for active checks.\\ Multiple comma-delimited addresses can be provided to use several independent Zabbix servers in parallel. No spaces allowed.\\ If port is not specified, default port is used.\\ IPv6 addresses must be enclosed in square brackets if port for that host is specified.\\ If port is not specified, square brackets for IPv6 addresses are optional.\\ If this parameter is not specified, active checks are disabled. | | ServerActive| no | (*) | |IP:port (or hostname:​port) of Zabbix server or Zabbix proxy for active checks.\\ Multiple comma-delimited addresses can be provided to use several independent Zabbix servers in parallel. No spaces allowed.\\ If port is not specified, default port is used.\\ IPv6 addresses must be enclosed in square brackets if port for that host is specified.\\ If port is not specified, square brackets for IPv6 addresses are optional.\\ If this parameter is not specified, active checks are disabled. |
 | SourceIP| no | | |Source IP address for outgoing connections. | | SourceIP| no | | |Source IP address for outgoing connections. |