Hello everyone,
I would like to ask for help to add several cisco switches to monitor the interfaces and device resources (CPU, memory).
I set up the SNMP option on the switches and add the devices in zabbix so the SNMP is working correctly. The is a screenshot below:
The problem is that I have tried with several of the cisco templates and the graphs for the CPU and memory are still empty with no data as below:
With the graphs for the interfaces there is not a problem:
The templates I tested are below and with all of them is the same problem.
Template Module Cisco CISCO-ENVMON-MIB SNMPv2
Template Module Cisco CISCO-MEMORY-POOL-MIB SNMPv2
Template Module Cisco CISCO-PROCESS-MIB IOS versions 12.0_3_T-12.2_3.5 SNMPv2
Template Module Cisco CISCO-PROCESS-MIB SNMPv2
Template Module Cisco Inventory SNMPv2
Template Module Cisco OLD-CISCO-CPU-MIB SNMPv2
Template Net Cisco IOS prior to 12.0_3_T SNMPv2
Template Net Cisco IOS SNMPv2
Template Net Cisco IOS versions 12.0_3_T-12.2_3.5 SNMPv2
Template Net Cisco Small Business 1.3 and 1.4 SNMPv2
Template Net Network Generic Device SNMPv1
Template Net Network Generic Device SNMPv2
Template Module Generic SNMPv1
Template Module Generic SNMPv2
Template Module HOST-RESOURCES-MIB SNMPv1
Template Module HOST-RESOURCES-MIB SNMPv2
The devices are Cisco SF300-48 and Cisco SG350-48. I have MIB files but as I was researching over the internet for days I found out that if I want to create a template, graphs screens is not possible to automate because MIB contains only description of raw metrics.
I also searched in this forum for a similar topic but I couldn't find a workable solution.
Thanks a lot if you could give any advice.
I would like to ask for help to add several cisco switches to monitor the interfaces and device resources (CPU, memory).
I set up the SNMP option on the switches and add the devices in zabbix so the SNMP is working correctly. The is a screenshot below:
The problem is that I have tried with several of the cisco templates and the graphs for the CPU and memory are still empty with no data as below:
With the graphs for the interfaces there is not a problem:
The templates I tested are below and with all of them is the same problem.
Template Module Cisco CISCO-ENVMON-MIB SNMPv2
Template Module Cisco CISCO-MEMORY-POOL-MIB SNMPv2
Template Module Cisco CISCO-PROCESS-MIB IOS versions 12.0_3_T-12.2_3.5 SNMPv2
Template Module Cisco CISCO-PROCESS-MIB SNMPv2
Template Module Cisco Inventory SNMPv2
Template Module Cisco OLD-CISCO-CPU-MIB SNMPv2
Template Net Cisco IOS prior to 12.0_3_T SNMPv2
Template Net Cisco IOS SNMPv2
Template Net Cisco IOS versions 12.0_3_T-12.2_3.5 SNMPv2
Template Net Cisco Small Business 1.3 and 1.4 SNMPv2
Template Net Network Generic Device SNMPv1
Template Net Network Generic Device SNMPv2
Template Module Generic SNMPv1
Template Module Generic SNMPv2
Template Module HOST-RESOURCES-MIB SNMPv1
Template Module HOST-RESOURCES-MIB SNMPv2
The devices are Cisco SF300-48 and Cisco SG350-48. I have MIB files but as I was researching over the internet for days I found out that if I want to create a template, graphs screens is not possible to automate because MIB contains only description of raw metrics.
I also searched in this forum for a similar topic but I couldn't find a workable solution.
Thanks a lot if you could give any advice.