monitoring hp 1810 switch

[hrickh]

hallo,

i have installed zabbix a few weeks ago and began monitoring several windows servers. so far so good.

now i want to monitor my hp 1810 switches bath i don't know how.
i have found an youtube link: https://www.youtube.com/watch?v=Wygx6t0fzMQ bath i cannot understand it because it is not english.
can sombody help me out with this i am new to the monitoring.

[aib]

1) Create a host for HP 1810 switch
2) Configure "SNMP Interfaces" (ip address)
3) Configure "Macros" -> {$SNMP_COMMUNITY} -> "public"
4) Add "Template SNMP Device"

[hrickh]

1) Create a host for HP 1810 switch
2) Configure "SNMP Interfaces" (ip address)
3) Configure "Macros" -> {$SNMP_COMMUNITY} -> "public"
4) Add "Template SNMP Device"

i have done that already
snmp interface port 161 (default)
bath snmp doesn't get any green lights
when i look under times i get error saying:
snmp_parse_oid(): cannot parse OID "IF-MIB::ifNumber.0".

[hrickh]

1) Create a host for HP 1810 switch
2) Configure "SNMP Interfaces" (ip address)
3) Configure "Macros" -> {$SNMP_COMMUNITY} -> "public"
4) Add "Template SNMP Device"

i also get the following error.
snmp_parse_oid(): cannot parse OID "SNMPv2-MIB::sysUpTime.0"

[aib]

It looks like you didn't install any MIB.

For Ubuntu try to run

apt-get install snmp-mibs-downloader

and reboot server

For additional info check the article:

https://l3net.wordpress.com/2013/05/12/installing-net-snmp-mibs-on-ubuntu-and-debian/

[hrickh]

It looks like you didn't install any MIB.

For Ubuntu try to run

apt-get install snmp-mibs-downloader

and reboot server

For additional info check the article:
https://l3net.wordpress.com/2013/05/...tu-and-debian/

thanks for your information.
i am using debian.
i have used the same command and it was installing.
rebooted the server.

i have also downloaded and modified the xml of the hp procurve 1810. there i will get a green check mark in the items list.

the switch is not available in the host list

[aib]

Switch can be available only(!) if Zabbix Agent connection works.
In case of SNMP device it will works, but Red Z letter will be on.

Just check twice that you have only one interface configured.

[hrickh]

Switch can be available only(!) if Zabbix Agent connection works.
In case of SNMP device it will works, but Red Z letter will be on.

Just check twice that you have only one interface configured.

thanks it works now.
i was forgot to run the following command: download-mibs

can you also help me with adding our vmware esxi host
i want to monitor network status, hardisk, memory usage, cpu usage,

[aib]

Start from documentation:

https://www.zabbix.com/documentation/2.4/manual/vm_monitoring

[hrickh]

Start from documentation:
https://www.zabbix.com/documentation.../vm_monitoring

thanks you for your response
i run already in some problem with discovery.
it says u need to use simple check.
in my list on discovery rule i do not have simple check
see atachment


issent there a way to manualy add the esx host?

[aib]

It's screenshot from different Discovery.
You need LLD (low-level discovery)

Check that documentation, starts from EXAMPLE.

[hrickh]

It's screenshot from different Discovery.
You need LLD (low-level discovery)

Check that documentation, starts from EXAMPLE.

i have add a new host.
entered macro's for password and username filled> in this information.
for url i entered: https://vmwareserverhostname/sdk ? is this correct
don't i need to fill in host information on snmp/jmx/ipmi interface?


--with-libxml2 and --with-libcurl) is default installed isn't it?
how to install when not? i have looked on https://www.zabbix.com/documentation...re_the_sources
bath i don't understand it

[aib]

Try

yum install -y gcc libxml2-devel libcurl-devel

[hrickh]

i got debian and you command diddent work i have runnned the following commands:

apt-get install curl libcurl3
apt-get install libxml2-dev


i hope this does the same?