Triggers will be created only for interfaces whose description contains the value of this macro

The time interval for SNMP agent availability trigger expression.

Type the minimum signal to noise margin (0-31 dB)

Type the maximum signal attenuation

Filter by discoverable interface names.

Filter to exclude discovered interfaces by name.

Filter by discoverable slot status.

Filter to exclude discovered slots by status.

Filter of discoverable link types.

Filter to exclude discovered by link types.

Preprocessing

• Discard unchanged with heartbeat: 1h

MIB: RFC1213-MIB

A textual description of the entity. This value

should include the full name and version

identification of the system's hardware type,

software operating-system, and networking

software. It is mandatory that this only contain

printable ASCII characters.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The textual identification of the contact person

for this managed node, together with information

on how to contact this person.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

An administratively-assigned name for this

managed node. By convention, this is the node's

fully-qualified domain name.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The physical location of this node (e.g.,

`telephone closet, 3rd floor').

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The interface's address at the protocol layer

immediately `below' the network layer in the

protocol stack. For interfaces which do not have

such an address (e.g., a serial line), this object

should contain an octet string of zero length.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The time (in hundredths of a second) since the

network management portion of the system was last

re-initialized.

Preprocessing

• Custom multiplier: 0.01

MIB: HOST-RESOURCES-MIB

The amount of time since this host was last initialized.

Note that this is different from sysUpTime in the SNMPv2-MIB

[RFC1907] because sysUpTime is the uptime of the

network management portion of the system.

Preprocessing

• Check for not supported value: any error

  ⛔️Custom on fail: Set value to: 0

• Custom multiplier: 0.01

SNMP is not available for polling. Please check device connectivity and SNMP settings.

This template is for Zyxel IES-6000, but connected to {ITEM.VALUE}

Uptime is less than 10 minutes.

The table which contains the slot information in a chassis.

MIB: ZYXEL-IES5000-MIB

Card type of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The descriptions of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The firmware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL driver of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL modem code version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The module state of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

This variable indicates the alarm status of the module.

It is a bit map represented a sum, therefore, it can represent

multiple defects simultaneously. The moduleNoDefect should be set

if and only if no other flag is set.

The various bit positions are:

1 moduleNoDefect

2 moduleOverHeat

3 moduleFanRpmLow

4 moduleVoltageLow

5 moduleThermalSensorFailure

6 modulePullOut

7 powerDC48VAFailure

8 powerDC48VBFailure

9 extAlarmInputTrigger

10 moduleDown

11 mscSwitchOverOK

12 networkTopologyChange

13 macSpoof

14 cpuHigh

15 memoryUsageHigh

16 packetBufferUsageHigh

17 loopguardOccurence

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The hardware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The serial number of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The time (in seconds) since the plug-in card was last re-initialized.

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

The slot reported an error.

Firmware version has changed. Acknowledge to close the problem manually.

Slot {#ZYXEL.SLOT.ID} serial number has changed. Acknowledge to close the problem manually.

Uptime is less than 10 minutes.

An entry in fanRpmTable.

MIB: ZYXEL-IES5000-MIB

Current speed in Revolutions Per Minute (RPM) on the fan.

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the fan unit

An entry in tempTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current temperature measured at this sensor

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the temperature

An entry in voltageTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current voltage reading.

Preprocessing

• Custom multiplier: 0.001

• Discard unchanged with heartbeat: 1h

Please check the power supply

A table that contains CPU utilization information.

This table is supported by R1.03 and later versions.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The CPU utilization in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The CPU utilization is too high. The system might be slow to respond.

A table that contains memory usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The memory usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free memory.

A table that contains packet buffer usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The packet buffer usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free buffer.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

An estimate of the interface's current bandwidth in bits per second

Preprocessing

• Custom multiplier: 1000000

• Discard unchanged with heartbeat: 6h

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. {$IFCONTROL:"{#IFNAME}"}=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. {TEMPLATE_NAME:METRIC.diff()}=1 - the trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. {$IFCONTROL:"{#IFNAME}"}=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. {TEMPLATE_NAME:METRIC.diff()}=1 - the trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Triggers will be created only for interfaces whose description contains the value of this macro

The time interval for SNMP agent availability trigger expression.

Type the minimum signal to noise margin (0-31 dB)

Type the maximum signal attenuation

Filter by discoverable interface names.

Filter to exclude discovered interfaces by name.

Filter by discoverable slot status.

Filter to exclude discovered slots by status.

Filter of discoverable link types.

Filter to exclude discovered by link types.

MIB: RFC1213-MIB

A textual description of the entity. This value

should include the full name and version

identification of the system's hardware type,

software operating-system, and networking

software. It is mandatory that this only contain

printable ASCII characters.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The textual identification of the contact person

for this managed node, together with information

on how to contact this person.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

An administratively-assigned name for this

managed node. By convention, this is the node's

fully-qualified domain name.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The physical location of this node (e.g.,

`telephone closet, 3rd floor').

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The interface's address at the protocol layer

immediately `below' the network layer in the

protocol stack. For interfaces which do not have

such an address (e.g., a serial line), this object

should contain an octet string of zero length.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The time (in hundredths of a second) since the

network management portion of the system was last

re-initialized.

Preprocessing

• Custom multiplier: 0.01

MIB: HOST-RESOURCES-MIB

The amount of time since this host was last initialized.

Note that this is different from sysUpTime in the SNMPv2-MIB

[RFC1907] because sysUpTime is the uptime of the

network management portion of the system.

Preprocessing

• Check for not supported value: any error

  ⛔️Custom on fail: Set value to: 0

• Custom multiplier: 0.01

SNMP is not available for polling. Please check device connectivity and SNMP settings.

This template is for Zyxel IES-6000, but connected to {ITEM.VALUE}

Uptime is less than 10 minutes.

The table which contains the slot information in a chassis.

MIB: ZYXEL-IES5000-MIB

Card type of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The descriptions of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The firmware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL driver of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL modem code version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The module state of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

This variable indicates the alarm status of the module.

It is a bit map represented a sum, therefore, it can represent

multiple defects simultaneously. The moduleNoDefect should be set

if and only if no other flag is set.

The various bit positions are:

1 moduleNoDefect

2 moduleOverHeat

3 moduleFanRpmLow

4 moduleVoltageLow

5 moduleThermalSensorFailure

6 modulePullOut

7 powerDC48VAFailure

8 powerDC48VBFailure

9 extAlarmInputTrigger

10 moduleDown

11 mscSwitchOverOK

12 networkTopologyChange

13 macSpoof

14 cpuHigh

15 memoryUsageHigh

16 packetBufferUsageHigh

17 loopguardOccurence

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The hardware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The serial number of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The time (in seconds) since the plug-in card was last re-initialized.

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

The slot reported an error.

Firmware version has changed. Acknowledge to close the problem manually.

Slot {#ZYXEL.SLOT.ID} serial number has changed. Acknowledge to close the problem manually.

Uptime is less than 10 minutes.

An entry in fanRpmTable.

MIB: ZYXEL-IES5000-MIB

Current speed in Revolutions Per Minute (RPM) on the fan.

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the fan unit

An entry in tempTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current temperature measured at this sensor

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the temperature

An entry in voltageTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current voltage reading.

Preprocessing

• Custom multiplier: 0.001

• Discard unchanged with heartbeat: 1h

Please check the power supply

A table that contains CPU utilization information.

This table is supported by R1.03 and later versions.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The CPU utilization in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The CPU utilization is too high. The system might be slow to respond.

A table that contains memory usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The memory usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free memory.

A table that contains packet buffer usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The packet buffer usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free buffer.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

An estimate of the interface's current bandwidth in bits per second

Preprocessing

• Custom multiplier: 1000000

• Discard unchanged with heartbeat: 6h

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. { $IFCONTROL:"{#IFNAME}" }=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. The trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. { $IFCONTROL:"{#IFNAME}" }=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. The trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Triggers will be created only for interfaces whose description contains the value of this macro

The time interval for SNMP agent availability trigger expression.

Type the minimum signal to noise margin (0-31 dB)

Type the maximum signal attenuation

Filter by discoverable interface names.

Filter to exclude discovered interfaces by name.

Filter by discoverable slot status.

Filter to exclude discovered slots by status.

Filter of discoverable link types.

Filter to exclude discovered by link types.

Preprocessing

• Discard unchanged with heartbeat: 1h

MIB: RFC1213-MIB

A textual description of the entity. This value

should include the full name and version

identification of the system's hardware type,

software operating-system, and networking

software. It is mandatory that this only contain

printable ASCII characters.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The textual identification of the contact person

for this managed node, together with information

on how to contact this person.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

An administratively-assigned name for this

managed node. By convention, this is the node's

fully-qualified domain name.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The physical location of this node (e.g.,

`telephone closet, 3rd floor').

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The interface's address at the protocol layer

immediately `below' the network layer in the

protocol stack. For interfaces which do not have

such an address (e.g., a serial line), this object

should contain an octet string of zero length.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The time (in hundredths of a second) since the

network management portion of the system was last

re-initialized.

Preprocessing

• Custom multiplier: 0.01

MIB: HOST-RESOURCES-MIB

The amount of time since this host was last initialized.

Note that this is different from sysUpTime in the SNMPv2-MIB

[RFC1907] because sysUpTime is the uptime of the

network management portion of the system.

Preprocessing

• Check for not supported value

  ⛔️Custom on fail: Set value to: 0

• Custom multiplier: 0.01

SNMP is not available for polling. Please check device connectivity and SNMP settings.

This template is for Zyxel IES-6000, but connected to {ITEM.VALUE}

Uptime is less than 10 minutes.

The table which contains the slot information in a chassis.

MIB: ZYXEL-IES5000-MIB

Card type of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The descriptions of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The firmware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL driver of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL modem code version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The module state of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

This variable indicates the alarm status of the module.

It is a bit map represented a sum, therefore, it can represent

multiple defects simultaneously. The moduleNoDefect should be set

if and only if no other flag is set.

The various bit positions are:

1 moduleNoDefect

2 moduleOverHeat

3 moduleFanRpmLow

4 moduleVoltageLow

5 moduleThermalSensorFailure

6 modulePullOut

7 powerDC48VAFailure

8 powerDC48VBFailure

9 extAlarmInputTrigger

10 moduleDown

11 mscSwitchOverOK

12 networkTopologyChange

13 macSpoof

14 cpuHigh

15 memoryUsageHigh

16 packetBufferUsageHigh

17 loopguardOccurence

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The hardware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The serial number of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The time (in seconds) since the plug-in card was last re-initialized.

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

Firmware version has changed. Acknowledge to close the problem manually.

The slot reported an error.

Firmware version has changed. Acknowledge to close the problem manually.

Slot {#ZYXEL.SLOT.ID} serial number has changed. Acknowledge to close the problem manually.

Uptime is less than 10 minutes.

An entry in fanRpmTable.

MIB: ZYXEL-IES5000-MIB

Current speed in Revolutions Per Minute (RPM) on the fan.

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the fan unit

An entry in tempTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current temperature measured at this sensor

Preprocessing

• Discard unchanged with heartbeat: 1h

Please check the temperature

An entry in voltageTable.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The current voltage reading.

Preprocessing

• Custom multiplier: 0.001

• Discard unchanged with heartbeat: 1h

Please check the power supply

A table that contains CPU utilization information.

This table is supported by R1.03 and later versions.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The CPU utilization in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The CPU utilization is too high. The system might be slow to respond.

A table that contains memory usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The memory usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free memory.

A table that contains packet buffer usage information.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The packet buffer usage in the past 60 seconds.

Preprocessing

• Discard unchanged with heartbeat: 1h

The system is running out of free buffer.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

An estimate of the interface's current bandwidth in bits per second

Preprocessing

• Custom multiplier: 1000000

• Discard unchanged with heartbeat: 6h

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

Interface utilization percentage

Preprocessing

• In range: 0 -> 100

  ⛔️Custom on fail: Discard value

• JavaScript: The text is too long. Please see the template.

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. {$IFCONTROL:"{#IFNAME}"}=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. {TEMPLATE_NAME:METRIC.diff()}=1 - the trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing

• Custom multiplier: 8

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing

• Change per second

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing

• Change per second

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit - Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit - Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing

• Custom multiplier: 0.1

• Discard unchanged with heartbeat: 1h

This trigger expression works as follows:
1. It can be triggered if the operations status is down.
2. {$IFCONTROL:"{#IFNAME}"}=1 - a user can redefine context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.
3. {TEMPLATE_NAME:METRIC.diff()}=1 - the trigger fires only if the operational status was up to (1) sometime before (so, do not fire for the 'eternal off' interfaces.)

WARNING: if closed manually - it will not fire again on the next poll, because of .diff.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

The time interval for SNMP agent availability trigger expression.

Type the maximum signal attenuation

Type the minimum signal to noise margin (0-31 dB)

Triggers will be created only for interfaces whose description contains the value of this macro

Filter by discoverable interface names.

Filter to exclude discovered interfaces by name.

Filter of discoverable link types.

Filter to exclude discovered by link types.

Filter by discoverable slot status.

Filter to exclude discovered slots by status.

-

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

Filter:

- {#ZYXEL.IF.DESC} MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.DESC.MATCHES}

- {#ZYXEL.IF.DESC} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.DESC.NOT_MATCHES}

- {#ZYXEL.IF.LINKSTATUS} MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.LINKSTATUS.MATCHES}

- {#ZYXEL.IF.LINKSTATUS} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.LINKSTATUS.NOT_MATCHES}

- {#ZYXEL.IF.NAME} MATCHES_REGEX adsl

Overrides:

Don't create triggers for matching interface
- {#ZYXEL.IF.NAME} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.CONTROL.MATCHES}
- TRIGGER_PROTOTYPE REGEXP .*
- NO_DISCOVER

A table that contains CPU utilization information.

This table is supported by R1.03 and later versions.

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

-

Filter:

- {#ZYXEL.IF.DESC} MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.DESC.MATCHES}

- {#ZYXEL.IF.DESC} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.DESC.NOT_MATCHES}

- {#ZYXEL.IF.LINKSTATUS} MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.LINKSTATUS.MATCHES}

- {#ZYXEL.IF.LINKSTATUS} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.LINKSTATUS.NOT_MATCHES}

- {#ZYXEL.IF.NAME} MATCHES_REGEX enet

Overrides:

Don't create triggers for matching interface
- {#ZYXEL.IF.NAME} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.IF.CONTROL.MATCHES}
- TRIGGER_PROTOTYPE REGEXP .*
- NO_DISCOVER

An entry in fanRpmTable.

A table that contains memory usage information.

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

A table that contains packet buffer usage information.

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

The table which contains the slot information in a chassis.

Filter:

- {#ZYXEL.SLOTSTATUS} MATCHES_REGEX {$ZYXEL.LLD.FILTER.SLOT.STATUS.MATCHES}

- {#ZYXEL.SLOTSTATUS} NOT_MATCHES_REGEX {$ZYXEL.LLD.FILTER.SLOT.STATUS.NOT_MATCHES}

An entry in tempTable.

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

An entry in voltageTable.

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The CPU utilization in the past 60 seconds.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ZYXEL-IES5000-MIB

Current speed in Revolutions Per Minute (RPM) on the fan.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: RFC1213-MIB

A textual description of the entity. This value

should include the full name and version

identification of the system's hardware type,

software operating-system, and networking

software. It is mandatory that this only contain

printable ASCII characters.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: RFC1213-MIB

The textual identification of the contact person

for this managed node, together with information

on how to contact this person.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: RFC1213-MIB

An administratively-assigned name for this

managed node. By convention, this is the node's

fully-qualified domain name.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: RFC1213-MIB

The physical location of this node (e.g.,

`telephone closet, 3rd floor').

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The interface's address at the protocol layer

immediately `below' the network layer in the

protocol stack. For interfaces which do not have

such an address (e.g., a serial line), this object

should contain an octet string of zero length.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The memory usage in the past 60 seconds.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ZYXEL-IES5000-MIB

The packet buffer usage in the past 60 seconds.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ZYXEL-IES5000-MIB

Card type of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The descriptions of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The firmware version of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The DSL driver of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The DSL modem code version of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The module state of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

This variable indicates the alarm status of the module.

It is a bit map represented a sum, therefore, it can represent

multiple defects simultaneously. The moduleNoDefect should be set

if and only if no other flag is set.

The various bit positions are:

1 moduleNoDefect

2 moduleOverHeat

3 moduleFanRpmLow

4 moduleVoltageLow

5 moduleThermalSensorFailure

6 modulePullOut

7 powerDC48VAFailure

8 powerDC48VBFailure

9 extAlarmInputTrigger

10 moduleDown

11 mscSwitchOverOK

12 networkTopologyChange

13 macSpoof

14 cpuHigh

15 memoryUsageHigh

16 packetBufferUsageHigh

17 loopguardOccurence

Preprocessing:

- JAVASCRIPT: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The hardware version of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The serial number of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The time (in seconds) since the plug-in card was last re-initialized.

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing:

- MULTIPLIER: 8

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing:

- MULTIPLIER: 8

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

An estimate of the interface's current bandwidth in bits per second

Preprocessing:

- MULTIPLIER: 1000000

- DISCARD_UNCHANGED_HEARTBEAT: 6h

Interface utilization percentage

Preprocessing:

- IN_RANGE: 0 100

⛔️ON_FAIL: DISCARD_VALUE ->

- JAVASCRIPT: return +parseFloat(value).toFixed(0);

Expression:

Interface utilization percentage

Preprocessing:

- IN_RANGE: 0 100

⛔️ON_FAIL: DISCARD_VALUE ->

- JAVASCRIPT: return +parseFloat(value).toFixed(0);

Expression:

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

A textual string containing information about the interface

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The current operational state of the interface.

The testing(3) state indicates that no operational

packets can be passed.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The desired state of the interface. The

testing(3) state indicates that no operational

packets can be passed.

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 6h

MIB: IF-MIB

The total number of octets received on the interface,

including framing characters.

Preprocessing:

- MULTIPLIER: 8

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were not addressed to a multicast

or broadcast address at this sub-layer

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a multicast

address at this sub-layer. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The number of packets, delivered by this sub-layer to a

higher (sub-)layer, which were addressed to a broadcast

address at this sub-layer.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of octets transmitted out of the

interface, including framing characters. This object is a

64-bit version of ifOutOctets.

Preprocessing:

- MULTIPLIER: 8

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were not addressed to a

multicast or broadcast address at this sub-layer, including

those that were discarded or not sent.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

multicast address at this sub-layer, including those that

were discarded or not sent. For a MAC layer protocol, this

includes both Group and Functional addresses.

Preprocessing:

- CHANGE_PER_SECOND

MIB: IF-MIB

The total number of packets that higher-level protocols

requested be transmitted, and which were addressed to a

broadcast address at this sub-layer, including those that

were discarded or not sent.

Preprocessing:

- CHANGE_PER_SECOND

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit – Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit – Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atuc fields show data acquired from the ATUC (ADSL Termination Unit – Central), in this case ZYXEL IES-6000, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ADSL-LINE-MIB

Noise Margin as seen by this ATU with respect to its

received signal in tenth dB.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit – Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ADSL-LINE-MIB

Measured difference in the total power transmitted by

the peer ATU and the total power received by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit – Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ADSL-LINE-MIB

Measured total output power transmitted by this ATU.

The Info Atur fields show data acquired from the ATUR (ADSL Termination Unit – Remote), in this case the subscriber's ADSL modem or router, during negotiation/provisioning message interchanges.

Preprocessing:

- MULTIPLIER: 0.1

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: ZYXEL-IES5000-MIB

The current voltage reading.

Preprocessing:

- MULTIPLIER: 0.001

- DISCARD_UNCHANGED_HEARTBEAT: 1h

-

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

MIB: RFC1213-MIB

The time (in hundredths of a second) since the

network management portion of the system was last

re-initialized.

Preprocessing:

- MULTIPLIER: 0.01

MIB: HOST-RESOURCES-MIB

The amount of time since this host was last initialized.

Note that this is different from sysUpTime in the SNMPv2-MIB

[RFC1907] because sysUpTime is the uptime of the

network management portion of the system.

Preprocessing:

- CHECK_NOT_SUPPORTED

⛔️ON_FAIL: CUSTOM_VALUE -> 0

- MULTIPLIER: 0.01

MIB: ZYXEL-IES5000-MIB

The current temperature measured at this sensor

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1h

CPU utilization is too high. The system might be slow to respond.

Please check the fan unit

This template is for Zyxel IES-6000, but connected to {ITEM.VALUE}

The system is running out of free memory.

The system is running out of free buffer.

Firmware version has changed. Ack to close

Manual close: YES

Firmware version has changed. Ack to close

Manual close: YES

Firmware version has changed. Ack to close

Manual close: YES

The slot reported an error.

Firmware version has changed. Ack to close

Manual close: YES

Slot {#ZYXEL.SLOT.ID} serial number has changed. Ack to close

Manual close: YES

Uptime is less than 10 minutes

Manual close: YES

This trigger expression works as follows:

1. Can be triggered if operations status is down.

2. {TEMPLATE_NAME:METRIC.diff()}=1) - trigger fires only if operational status was up(1) sometime before. (So, do not fire 'ethernal off' interfaces.)

WARNING: if closed manually - won't fire again on next poll, because of .diff.

Recovery expression:

Manual close: YES

This trigger expression works as follows:

1. Can be triggered if operations status is down.

2. {TEMPLATE_NAME:METRIC.diff()}=1) - trigger fires only if operational status was up(1) sometime before. (So, do not fire 'ethernal off' interfaces.)

WARNING: if closed manually - won't fire again on next poll, because of .diff.

Recovery expression:

Manual close: YES

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Signal-to-noise margin (SNR Margin) which is the difference between the actual SNR and the SNR required to sync at a specific speed

The reductions in amplitude of the downstream and upstream DSL signals.

Please check the power supply

SNMP is not available for polling. Please check device connectivity and SNMP settings.

Uptime is less than 10 minutes.

Manual close: YES

Please check the temperature

Triggers will be created only for interfaces whose description contains the value of this macro

The time interval for SNMP agent availability trigger expression.

Type the minimum signal to noise margin (0-31 dB)

Type the maximum signal attenuation

Filter by discoverable interface names.

Filter to exclude discovered interfaces by name.

Filter by discoverable slot status.

Filter to exclude discovered slots by status.

Filter of discoverable link types.

Filter to exclude discovered by link types.

Preprocessing

• Discard unchanged with heartbeat: 1h

MIB: RFC1213-MIB

A textual description of the entity. This value

should include the full name and version

identification of the system's hardware type,

software operating-system, and networking

software. It is mandatory that this only contain

printable ASCII characters.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The textual identification of the contact person

for this managed node, together with information

on how to contact this person.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

An administratively-assigned name for this

managed node. By convention, this is the node's

fully-qualified domain name.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The physical location of this node (e.g.,

`telephone closet, 3rd floor').

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: IF-MIB

The interface's address at the protocol layer

immediately `below' the network layer in the

protocol stack. For interfaces which do not have

such an address (e.g., a serial line), this object

should contain an octet string of zero length.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: RFC1213-MIB

The time (in hundredths of a second) since the

network management portion of the system was last

re-initialized.

Preprocessing

• Custom multiplier: 0.01

MIB: HOST-RESOURCES-MIB

The amount of time since this host was last initialized.

Note that this is different from sysUpTime in the SNMPv2-MIB

[RFC1907] because sysUpTime is the uptime of the

network management portion of the system.

Preprocessing

• Check for not supported value

  ⛔️Custom on fail: Set value to: 0

• Custom multiplier: 0.01

SNMP is not available for polling. Please check device connectivity and SNMP settings.

This template is for Zyxel IES-6000, but connected to {ITEM.VALUE}

Uptime is less than 10 minutes.

The table which contains the slot information in a chassis.

MIB: ZYXEL-IES5000-MIB

Card type of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The descriptions of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The firmware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL driver of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The DSL modem code version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The module state of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

This variable indicates the alarm status of the module.

It is a bit map represented a sum, therefore, it can represent

multiple defects simultaneously. The moduleNoDefect should be set

if and only if no other flag is set.

The various bit positions are:

1 moduleNoDefect

2 moduleOverHeat

3 moduleFanRpmLow

4 moduleVoltageLow

5 moduleThermalSensorFailure

6 modulePullOut

7 powerDC48VAFailure

8 powerDC48VBFailure

9 extAlarmInputTrigger

10 moduleDown

11 mscSwitchOverOK

12 networkTopologyChange

13 macSpoof

14 cpuHigh

15 memoryUsageHigh

16 packetBufferUsageHigh

17 loopguardOccurence

Preprocessing

• JavaScript: The text is too long. Please see the template.

MIB: ZYXEL-IES5000-MIB

The hardware version of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The serial number of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The time (in seconds) since the plug-in card was last re-initialized.

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.

Preprocessing

• Discard unchanged with heartbeat: 6h

MIB: ZYXEL-IES5000-MIB

The MAC Address of the plug-in card.