Available solutions

Supermicro Aten SNMP
3rd party solutions

This template is for Zabbix version: 7.0

Also available for: 6.4 6.2 6.0 5.4 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/7.0

Supermicro Aten by SNMP

Overview

for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

Requirements

Zabbix version: 7.0 and higher.

Tested versions

This template has been tested on:

Supermicro X10DRI

Configuration

Zabbix should be configured according to the instructions in the Templates out of the box section.

Setup

Refer to the vendor documentation.

Macros used

Name	Description	Default
{$TEMP_CRIT}		`60`
{$TEMP_CRIT_LOW}		`5`
{$TEMP_WARN}		`50`
{$SNMP.TIMEOUT}	Time interval for the SNMP availability trigger.	`5m`
{$ICMP_LOSS_WARN}	Warning threshold of ICMP packet loss in %.	`20`
{$ICMP_RESPONSE_TIME_WARN}	Warning threshold of the average ICMP response time in seconds.	`0.15`

Items

Name	Description	Type	Key and additional info
Uptime (network)	MIB: SNMPv2-MIB Time (in hundredths of a second) since the network management portion of the system was last re-initialized.	SNMP agent	system.net.uptime[sysUpTime.0] Preprocessing Custom multiplier: `0.01`
Uptime (hardware)	MIB: HOST-RESOURCES-MIB The amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.	SNMP agent	system.hw.uptime[hrSystemUptime.0] Preprocessing Check for not supported value: `any error` ⛔️Custom on fail: Set value to: `0` Custom multiplier: `0.01`
SNMP traps (fallback)	The item is used to collect all SNMP traps unmatched by other snmptrap items	SNMP trap	snmptrap.fallback
System location	MIB: SNMPv2-MIB Physical location of the node (e.g., `equipment room`, `3rd floor`). If not provided, the value is a zero-length string.	SNMP agent	system.location[sysLocation.0] Preprocessing Discard unchanged with heartbeat: `12h`
System contact details	MIB: SNMPv2-MIB The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.	SNMP agent	system.contact[sysContact.0] Preprocessing Discard unchanged with heartbeat: `12h`
System object ID	MIB: SNMPv2-MIB The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining`what kind of box' is being managed. For example, if vendor`Flintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.	SNMP agent	system.objectid[sysObjectID.0] Preprocessing Discard unchanged with heartbeat: `12h`
System name	MIB: SNMPv2-MIB An administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.	SNMP agent	system.name Preprocessing Discard unchanged with heartbeat: `12h`
System description	MIB: SNMPv2-MIB A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software.	SNMP agent	system.descr[sysDescr.0] Preprocessing Discard unchanged with heartbeat: `12h`
SNMP agent availability	Availability of SNMP checks on the host. The value of this item corresponds to availability icons in the host list. Possible values: 0 - not available 1 - available 2 - unknown	Zabbix internal	zabbix[host,snmp,available]
ICMP ping		Simple check	icmpping
ICMP loss		Simple check	icmppingloss
ICMP response time		Simple check	icmppingsec

Triggers

Name	Description	Expression	Severity	Dependencies and additional info
Supermicro Aten: Host has been restarted	Uptime is less than 10 minutes.	`(last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])>0 and last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])<10m) or (last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])=0 and last(/Supermicro Aten by SNMP/system.net.uptime[sysUpTime.0])<10m)`	Warning	Manual close: Yes Depends on: Supermicro Aten: No SNMP data collection
Supermicro Aten: System name has changed	The name of the system has changed. Acknowledge to close the problem manually.	`last(/Supermicro Aten by SNMP/system.name,#1)<>last(/Supermicro Aten by SNMP/system.name,#2) and length(last(/Supermicro Aten by SNMP/system.name))>0`	Info	Manual close: Yes
Supermicro Aten: No SNMP data collection	SNMP is not available for polling. Please check device connectivity and SNMP settings.	`max(/Supermicro Aten by SNMP/zabbix[host,snmp,available],{$SNMP.TIMEOUT})=0`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: Unavailable by ICMP ping	Last three attempts returned timeout. Please check device connectivity.	`max(/Supermicro Aten by SNMP/icmpping,#3)=0`	High
Supermicro Aten: High ICMP ping loss		`min(/Supermicro Aten by SNMP/icmppingloss,5m)>{$ICMP_LOSS_WARN} and min(/Supermicro Aten by SNMP/icmppingloss,5m)<100`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: High ICMP ping response time	Average ICMP response time is too high.	`avg(/Supermicro Aten by SNMP/icmppingsec,5m)>{$ICMP_RESPONSE_TIME_WARN}`	Warning	Depends on: Supermicro Aten: High ICMP ping loss Supermicro Aten: Unavailable by ICMP ping

LLD rule Temperature Discovery

Name	Description	Type	Key and additional info
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP agent	tempDescr.discovery

Item prototypes for Temperature Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Temperature	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.temp.value[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Temperature

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.temp.value[sensorReading.{#SNMPINDEX}]

Trigger prototypes for Temperature Discovery

Name	Description	Expression	Severity	Dependencies and additional info
Supermicro Aten: {#SENSOR_DESCR}: Temperature is above warning threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:"{#SENSOR_DESCR}"}`	Warning	Depends on: Supermicro Aten: {#SENSOR_DESCR}: Temperature is above critical threshold
Supermicro Aten: {#SENSOR_DESCR}: Temperature is above critical threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:"{#SENSOR_DESCR}"}`	High
Supermicro Aten: {#SENSOR_DESCR}: Temperature is too low		`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:"{#SENSOR_DESCR}"}`	Average

LLD rule FAN Discovery

Name	Description	Type	Key and additional info
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP agent	fan.discovery

Item prototypes for FAN Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Fan speed, %	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Fan speed, %

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Feedback

Please report any issues with the template at https://support.zabbix.com

You can also provide feedback, discuss the template, or ask for help at ZABBIX forums

This template is for Zabbix version: 6.4

Also available for: 7.0 6.2 6.0 5.4 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/6.4

Supermicro Aten by SNMP

Overview

for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

Requirements

Zabbix version: 6.4 and higher.

Tested versions

This template has been tested on:

Supermicro X10DRI

Configuration

Zabbix should be configured according to the instructions in the Templates out of the box section.

Setup

Refer to the vendor documentation.

Macros used

Name	Description	Default
{$TEMP_CRIT}		`60`
{$TEMP_CRIT_LOW}		`5`
{$TEMP_WARN}		`50`
{$SNMP.TIMEOUT}		`5m`
{$ICMP_LOSS_WARN}		`20`
{$ICMP_RESPONSE_TIME_WARN}		`0.15`

Items

Name	Description	Type	Key and additional info
Supermicro Aten: Uptime (network)	MIB: SNMPv2-MIB The time (in hundredths of a second) since the network management portion of the system was last re-initialized.	SNMP agent	system.net.uptime[sysUpTime.0] Preprocessing Custom multiplier: `0.01`
Supermicro Aten: Uptime (hardware)	MIB: HOST-RESOURCES-MIB The amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.	SNMP agent	system.hw.uptime[hrSystemUptime.0] Preprocessing Check for not supported value ⛔️Custom on fail: Set value to: `0` Custom multiplier: `0.01`
Supermicro Aten: SNMP traps (fallback)	The item is used to collect all SNMP traps unmatched by other snmptrap items	SNMP trap	snmptrap.fallback
Supermicro Aten: System location	MIB: SNMPv2-MIB The physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.	SNMP agent	system.location[sysLocation.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System contact details	MIB: SNMPv2-MIB The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.	SNMP agent	system.contact[sysContact.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System object ID	MIB: SNMPv2-MIB The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining`what kind of box' is being managed. For example, if vendor`Flintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.	SNMP agent	system.objectid[sysObjectID.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System name	MIB: SNMPv2-MIB An administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.	SNMP agent	system.name Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System description	MIB: SNMPv2-MIB A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software.	SNMP agent	system.descr[sysDescr.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: SNMP agent availability	Availability of SNMP checks on the host. The value of this item corresponds to availability icons in the host list. Possible value: 0 - not available 1 - available 2 - unknown	Zabbix internal	zabbix[host,snmp,available]
Supermicro Aten: ICMP ping		Simple check	icmpping
Supermicro Aten: ICMP loss		Simple check	icmppingloss
Supermicro Aten: ICMP response time		Simple check	icmppingsec

Triggers

Name	Description	Expression	Severity	Dependencies and additional info
Supermicro Aten: Host has been restarted	Uptime is less than 10 minutes.	`(last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])>0 and last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])<10m) or (last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])=0 and last(/Supermicro Aten by SNMP/system.net.uptime[sysUpTime.0])<10m)`	Warning	Manual close: Yes Depends on: Supermicro Aten: No SNMP data collection
Supermicro Aten: System name has changed	The name of the system has changed. Acknowledge to close the problem manually.	`last(/Supermicro Aten by SNMP/system.name,#1)<>last(/Supermicro Aten by SNMP/system.name,#2) and length(last(/Supermicro Aten by SNMP/system.name))>0`	Info	Manual close: Yes
Supermicro Aten: No SNMP data collection	SNMP is not available for polling. Please check device connectivity and SNMP settings.	`max(/Supermicro Aten by SNMP/zabbix[host,snmp,available],{$SNMP.TIMEOUT})=0`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: Unavailable by ICMP ping	Last three attempts returned timeout. Please check device connectivity.	`max(/Supermicro Aten by SNMP/icmpping,#3)=0`	High
Supermicro Aten: High ICMP ping loss		`min(/Supermicro Aten by SNMP/icmppingloss,5m)>{$ICMP_LOSS_WARN} and min(/Supermicro Aten by SNMP/icmppingloss,5m)<100`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: High ICMP ping response time		`avg(/Supermicro Aten by SNMP/icmppingsec,5m)>{$ICMP_RESPONSE_TIME_WARN}`	Warning	Depends on: Supermicro Aten: High ICMP ping loss Supermicro Aten: Unavailable by ICMP ping

LLD rule Temperature Discovery

Name	Description	Type	Key and additional info
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP agent	tempDescr.discovery

Item prototypes for Temperature Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Temperature	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.temp.value[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Temperature

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.temp.value[sensorReading.{#SNMPINDEX}]

Trigger prototypes for Temperature Discovery

Name	Description	Expression	Severity	Dependencies and additional info
{#SENSOR_DESCR}: Temperature is above warning threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:"{#SENSOR_DESCR}"}`	Warning	Depends on: {#SENSOR_DESCR}: Temperature is above critical threshold
{#SENSOR_DESCR}: Temperature is above critical threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:"{#SENSOR_DESCR}"}`	High
{#SENSOR_DESCR}: Temperature is too low		`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:"{#SENSOR_DESCR}"}`	Average

LLD rule FAN Discovery

Name	Description	Type	Key and additional info
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP agent	fan.discovery

Item prototypes for FAN Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Fan speed, %	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Fan speed, %

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Feedback

Please report any issues with the template at https://support.zabbix.com

You can also provide feedback, discuss the template, or ask for help at ZABBIX forums

This template is for Zabbix version: 6.2

Also available for: 7.0 6.4 6.0 5.4 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/6.2

Supermicro Aten by SNMP

Overview

For Zabbix version: 6.2 and higher. for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

This template was tested on:

Supermicro X10DRI

Setup

Refer to the vendor documentation.

Zabbix configuration

No specific Zabbix configuration is required.

Macros used

Name	Description	Default
{$ICMP_LOSS_WARN}	-	`20`
{$ICMP_RESPONSE_TIME_WARN}	-	`0.15`
{$SNMP.TIMEOUT}	-	`5m`
{$TEMP_CRIT_LOW}	-	`5`
{$TEMP_CRIT}	-	`60`
{$TEMP_WARN}	-	`50`

Template links

There are no template links in this template.

Discovery rules

Name Description Type Key and additional info

FAN Discovery

Name	Description	Type	Key and additional info
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP	fan.discovery Filter: AND - {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - {#SENSOR_DESCR} MATCHES_REGEX `FAN.*`
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP	tempDescr.discovery Filter: AND - {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - {#SENSOR_DESCR} MATCHES_REGEX `.Temp.`

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)

SNMP

fan.discovery

Filter:

AND

- {#SNMPVALUE} MATCHES_REGEX [1-9]+

- {#SENSOR_DESCR} MATCHES_REGEX FAN.*

Temperature Discovery

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)

SNMP

tempDescr.discovery

Filter:

AND

- {#SNMPVALUE} MATCHES_REGEX [1-9]+

- {#SENSOR_DESCR} MATCHES_REGEX .*Temp.*

Items collected

Group	Name	Description	Type	Key and additional info
Fans	{#SENSOR_DESCR}: Fan speed, %	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP	sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]
General	SNMP traps (fallback)	The item is used to collect all SNMP traps unmatched by other snmptrap items	SNMP_TRAP	snmptrap.fallback
General	System location	MIB: SNMPv2-MIB The physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.	SNMP	system.location[sysLocation.0] Preprocessing: - DISCARD_UNCHANGED_HEARTBEAT: `12h`
General	System contact details	MIB: SNMPv2-MIB The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.	SNMP	system.contact[sysContact.0] Preprocessing: - DISCARD_UNCHANGED_HEARTBEAT: `12h`
General	System object ID	MIB: SNMPv2-MIB The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining`what kind of box' is being managed. For example, if vendor`Flintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.	SNMP	system.objectid[sysObjectID.0] Preprocessing: - DISCARD_UNCHANGED_HEARTBEAT: `12h`
General	System name	MIB: SNMPv2-MIB An administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.	SNMP	system.name Preprocessing: - DISCARD_UNCHANGED_HEARTBEAT: `12h`
General	System description	MIB: SNMPv2-MIB A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software.	SNMP	system.descr[sysDescr.0] Preprocessing: - DISCARD_UNCHANGED_HEARTBEAT: `12h`
Status	Uptime (network)	MIB: SNMPv2-MIB The time (in hundredths of a second) since the network management portion of the system was last re-initialized.	SNMP	system.net.uptime[sysUpTime.0] Preprocessing: - MULTIPLIER: `0.01`
Status	Uptime (hardware)	MIB: HOST-RESOURCES-MIB The amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.	SNMP	system.hw.uptime[hrSystemUptime.0] Preprocessing: - CHECK_NOT_SUPPORTED ⛔️ON_FAIL: `CUSTOM_VALUE -> 0` - MULTIPLIER: `0.01`
Status	SNMP agent availability	Availability of SNMP checks on the host. The value of this item corresponds to availability icons in the host list. Possible value: 0 - not available 1 - available 2 - unknown	INTERNAL	zabbix[host,snmp,available]
Status	ICMP ping	-	SIMPLE	icmpping
Status	ICMP loss	-	SIMPLE	icmppingloss
Status	ICMP response time	-	SIMPLE	icmppingsec
Temperature	{#SENSOR_DESCR}: Temperature	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP	sensor.temp.value[sensorReading.{#SNMPINDEX}]

Triggers

Name	Description	Expression	Severity	Dependencies and additional info
System name has changed	System name has changed. Ack to close.	`last(/Supermicro Aten by SNMP/system.name,#1)<>last(/Supermicro Aten by SNMP/system.name,#2) and length(last(/Supermicro Aten by SNMP/system.name))>0`	INFO	Manual close: YES
Host has been restarted	Uptime is less than 10 minutes.	`(last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])>0 and last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])<10m) or (last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])=0 and last(/Supermicro Aten by SNMP/system.net.uptime[sysUpTime.0])<10m)`	WARNING	Manual close: YES Depends on: - No SNMP data collection
No SNMP data collection	SNMP is not available for polling. Please check device connectivity and SNMP settings.	`max(/Supermicro Aten by SNMP/zabbix[host,snmp,available],{$SNMP.TIMEOUT})=0`	WARNING	Depends on: - Unavailable by ICMP ping
Unavailable by ICMP ping	Last three attempts returned timeout. Please check device connectivity.	`max(/Supermicro Aten by SNMP/icmpping,#3)=0`	HIGH
High ICMP ping loss	-	`min(/Supermicro Aten by SNMP/icmppingloss,5m)>{$ICMP_LOSS_WARN} and min(/Supermicro Aten by SNMP/icmppingloss,5m)<100`	WARNING	Depends on: - Unavailable by ICMP ping
High ICMP ping response time	-	`avg(/Supermicro Aten by SNMP/icmppingsec,5m)>{$ICMP_RESPONSE_TIME_WARN}`	WARNING	Depends on: - High ICMP ping loss - Unavailable by ICMP ping
{#SENSOR_DESCR}: Temperature is above warning threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:"{#SENSOR_DESCR}"}` Recovery expression: `max(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_WARN:"{#SENSOR_DESCR}"}-3`	WARNING	Depends on: - {#SENSOR_DESCR}: Temperature is above critical threshold
{#SENSOR_DESCR}: Temperature is above critical threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:"{#SENSOR_DESCR}"}` Recovery expression: `max(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT:"{#SENSOR_DESCR}"}-3`	HIGH
{#SENSOR_DESCR}: Temperature is too low	-	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:"{#SENSOR_DESCR}"}` Recovery expression: `min(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT_LOW:"{#SENSOR_DESCR}"}+3`	AVERAGE

Feedback

Please report any issues with the template at https://support.zabbix.com.

This template is for Zabbix version: 6.0

Also available for: 7.0 6.4 6.2 5.4 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/6.0

Supermicro Aten by SNMP

Overview

for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

Requirements

Zabbix version: 6.0 and higher.

Tested versions

This template has been tested on:

Supermicro X10DRI

Configuration

Zabbix should be configured according to the instructions in the Templates out of the box section.

Setup

Refer to the vendor documentation.

Macros used

Name	Description	Default
{$TEMP_CRIT}		`60`
{$TEMP_CRIT_LOW}		`5`
{$TEMP_WARN}		`50`
{$SNMP.TIMEOUT}		`5m`
{$ICMP_LOSS_WARN}		`20`
{$ICMP_RESPONSE_TIME_WARN}		`0.15`

Items

Name	Description	Type	Key and additional info
Supermicro Aten: Uptime (network)	MIB: SNMPv2-MIB The time (in hundredths of a second) since the network management portion of the system was last re-initialized.	SNMP agent	system.net.uptime[sysUpTime.0] Preprocessing Custom multiplier: `0.01`
Supermicro Aten: Uptime (hardware)	MIB: HOST-RESOURCES-MIB The amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.	SNMP agent	system.hw.uptime[hrSystemUptime.0] Preprocessing Check for not supported value ⛔️Custom on fail: Set value to: `0` Custom multiplier: `0.01`
Supermicro Aten: SNMP traps (fallback)	The item is used to collect all SNMP traps unmatched by other snmptrap items	SNMP trap	snmptrap.fallback
Supermicro Aten: System location	MIB: SNMPv2-MIB The physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.	SNMP agent	system.location[sysLocation.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System contact details	MIB: SNMPv2-MIB The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.	SNMP agent	system.contact[sysContact.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System object ID	MIB: SNMPv2-MIB The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining`what kind of box' is being managed. For example, if vendor`Flintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.	SNMP agent	system.objectid[sysObjectID.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System name	MIB: SNMPv2-MIB An administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.	SNMP agent	system.name Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: System description	MIB: SNMPv2-MIB A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software.	SNMP agent	system.descr[sysDescr.0] Preprocessing Discard unchanged with heartbeat: `12h`
Supermicro Aten: SNMP agent availability	Availability of SNMP checks on the host. The value of this item corresponds to availability icons in the host list. Possible value: 0 - not available 1 - available 2 - unknown	Zabbix internal	zabbix[host,snmp,available]
Supermicro Aten: ICMP ping		Simple check	icmpping
Supermicro Aten: ICMP loss		Simple check	icmppingloss
Supermicro Aten: ICMP response time		Simple check	icmppingsec

Triggers

Name	Description	Expression	Severity	Dependencies and additional info
Supermicro Aten: Host has been restarted	Uptime is less than 10 minutes.	`(last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])>0 and last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])<10m) or (last(/Supermicro Aten by SNMP/system.hw.uptime[hrSystemUptime.0])=0 and last(/Supermicro Aten by SNMP/system.net.uptime[sysUpTime.0])<10m)`	Warning	Manual close: Yes Depends on: Supermicro Aten: No SNMP data collection
Supermicro Aten: System name has changed	The name of the system has changed. Acknowledge to close the problem manually.	`last(/Supermicro Aten by SNMP/system.name,#1)<>last(/Supermicro Aten by SNMP/system.name,#2) and length(last(/Supermicro Aten by SNMP/system.name))>0`	Info	Manual close: Yes
Supermicro Aten: No SNMP data collection	SNMP is not available for polling. Please check device connectivity and SNMP settings.	`max(/Supermicro Aten by SNMP/zabbix[host,snmp,available],{$SNMP.TIMEOUT})=0`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: Unavailable by ICMP ping	Last three attempts returned timeout. Please check device connectivity.	`max(/Supermicro Aten by SNMP/icmpping,#3)=0`	High
Supermicro Aten: High ICMP ping loss		`min(/Supermicro Aten by SNMP/icmppingloss,5m)>{$ICMP_LOSS_WARN} and min(/Supermicro Aten by SNMP/icmppingloss,5m)<100`	Warning	Depends on: Supermicro Aten: Unavailable by ICMP ping
Supermicro Aten: High ICMP ping response time		`avg(/Supermicro Aten by SNMP/icmppingsec,5m)>{$ICMP_RESPONSE_TIME_WARN}`	Warning	Depends on: Supermicro Aten: High ICMP ping loss Supermicro Aten: Unavailable by ICMP ping

LLD rule Temperature Discovery

Name	Description	Type	Key and additional info
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP agent	tempDescr.discovery

Item prototypes for Temperature Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Temperature	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.temp.value[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Temperature

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.temp.value[sensorReading.{#SNMPINDEX}]

Trigger prototypes for Temperature Discovery

Name	Description	Expression	Severity	Dependencies and additional info
{#SENSOR_DESCR}: Temperature is above warning threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:"{#SENSOR_DESCR}"}`	Warning	Depends on: {#SENSOR_DESCR}: Temperature is above critical threshold
{#SENSOR_DESCR}: Temperature is above critical threshold	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:"{#SENSOR_DESCR}"}`	High
{#SENSOR_DESCR}: Temperature is too low		`avg(/Supermicro Aten by SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:"{#SENSOR_DESCR}"}`	Average

LLD rule FAN Discovery

Name	Description	Type	Key and additional info
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP agent	fan.discovery

Item prototypes for FAN Discovery

Name	Description	Type	Key and additional info
{#SENSOR_DESCR}: Fan speed, %	MIB: ATEN-IPMI-MIB A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	SNMP agent	sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Name

Description

Type

Key and additional info

{#SENSOR_DESCR}: Fan speed, %

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP agent

sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Feedback

Please report any issues with the template at https://support.zabbix.com

You can also provide feedback, discuss the template, or ask for help at ZABBIX forums

This template is for Zabbix version: 5.4

Also available for: 7.0 6.4 6.2 6.0 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/5.4

Supermicro Aten SNMP

Overview

For Zabbix version: 5.4 and higher
for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

This template was tested on:

Supermicro X10DRI

Setup

Refer to the vendor documentation.

Zabbix configuration

No specific Zabbix configuration is required.

Macros used

Name	Description	Default
{$TEMP_CRIT_LOW}	-	`5`
{$TEMP_CRIT}	-	`60`
{$TEMP_WARN}	-	`50`

Template links

Name
Generic SNMP

Discovery rules

Name Description Type Key and additional info

Temperature Discovery

Name	Description	Type	Key and additional info
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP	tempDescr.discovery Filter: AND - {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - {#SENSOR_DESCR} MATCHES_REGEX `.Temp.`
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP	fan.discovery Filter: AND - {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - {#SENSOR_DESCR} MATCHES_REGEX `FAN.*`

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)

SNMP

tempDescr.discovery

Filter:

AND

- {#SNMPVALUE} MATCHES_REGEX [1-9]+

- {#SENSOR_DESCR} MATCHES_REGEX .*Temp.*

FAN Discovery

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)

SNMP

fan.discovery

Filter:

AND

- {#SNMPVALUE} MATCHES_REGEX [1-9]+

- {#SENSOR_DESCR} MATCHES_REGEX FAN.*

Items collected

Group

Name

Description

Type

Key and additional info

Fans

{#SENSOR_DESCR}: Fan speed, %

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP

sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Temperature

{#SENSOR_DESCR}: Temperature

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP

sensor.temp.value[sensorReading.{#SNMPINDEX}]

Triggers

Name Description Expression Severity Dependencies and additional info

{#SENSOR_DESCR}: Temperature is above warning threshold: >{$TEMP_WARN:""}

Name	Description	Expression	Severity	Dependencies and additional info
{#SENSOR_DESCR}: Temperature is above warning threshold: >{$TEMP_WARN:""}	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:""}` Recovery expression: `max(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_WARN:""}-3`	WARNING	Depends on: - {#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}
{#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}	This trigger uses temperature sensor values as well as temperature sensor status if available	`avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:""}` Recovery expression: `max(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT:""}-3`	HIGH
{#SENSOR_DESCR}: Temperature is too low: <{$TEMP_CRIT_LOW:""}	-	`avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:""}` Recovery expression: `min(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT_LOW:""}+3`	AVERAGE

This trigger uses temperature sensor values as well as temperature sensor status if available

avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_WARN:""}

Recovery expression:

max(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_WARN:""}-3

WARNING

Depends on:

- {#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}

{#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}

This trigger uses temperature sensor values as well as temperature sensor status if available

avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT:""}

Recovery expression:

max(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT:""}-3

HIGH

{#SENSOR_DESCR}: Temperature is too low: <{$TEMP_CRIT_LOW:""}

avg(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:""}

Recovery expression:

min(/Supermicro Aten SNMP/sensor.temp.value[sensorReading.{#SNMPINDEX}],5m)>{$TEMP_CRIT_LOW:""}+3

AVERAGE

Feedback

Please report any issues with the template at https://support.zabbix.com

This template is for Zabbix version: 5.0

Also available for: 7.0 6.4 6.2 6.0 5.4

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/server/supermicro_aten_snmp?at=release/5.0

Template Server Supermicro Aten SNMP

Overview

For Zabbix version: 5.0 and higher
for BMC ATEN IPMI controllers of Supermicro servers https://www.supermicro.com/solutions/IPMI.cfm

This template was tested on:

Supermicro X10DRI

Setup

Refer to the vendor documentation.

Zabbix configuration

No specific Zabbix configuration is required.

Macros used

Name	Description	Default
{$TEMP_CRIT_LOW}	-	`5`
{$TEMP_CRIT}	-	`60`
{$TEMP_WARN}	-	`50`

Template links

Name
Generic SNMP

Discovery rules

Name Description Type Key and additional info

Temperature Discovery

Name	Description	Type	Key and additional info
Temperature Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)	SNMP	tempDescr.discovery Filter: AND - B: {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - A: {#SENSOR_DESCR} MATCHES_REGEX `.Temp.`
FAN Discovery	Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)	SNMP	fan.discovery Filter: AND - B: {#SNMPVALUE} MATCHES_REGEX `[1-9]+` - A: {#SENSOR_DESCR} MATCHES_REGEX `FAN.*`

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected temp sensors (Value = 0)

SNMP

tempDescr.discovery

Filter:

AND

- B: {#SNMPVALUE} MATCHES_REGEX [1-9]+

- A: {#SENSOR_DESCR} MATCHES_REGEX .*Temp.*

FAN Discovery

Scanning ATEN-IPMI-MIB::sensorTable with filter: not connected FAN sensors (Value = 0)

SNMP

fan.discovery

Filter:

AND

- B: {#SNMPVALUE} MATCHES_REGEX [1-9]+

- A: {#SENSOR_DESCR} MATCHES_REGEX FAN.*

Items collected

Group

Name

Description

Type

Key and additional info

Fans

{#SENSOR_DESCR}: Fan speed, %

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP

sensor.fan.speed.percentage[sensorReading.{#SNMPINDEX}]

Temperature

{#SENSOR_DESCR}: Temperature

MIB: ATEN-IPMI-MIB

A textual string containing information about the interface.

This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

SNMP

sensor.temp.value[sensorReading.{#SNMPINDEX}]

Triggers

Name Description Expression Severity Dependencies and additional info

{#SENSOR_DESCR}: Temperature is above warning threshold: >{$TEMP_WARN:""}

Name	Description	Expression	Severity	Dependencies and additional info
{#SENSOR_DESCR}: Temperature is above warning threshold: >{$TEMP_WARN:""}	This trigger uses temperature sensor values as well as temperature sensor status if available	`{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}>{$TEMP_WARN:""}` Recovery expression: `{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].max(5m)}<{$TEMP_WARN:""}-3`	WARNING	Depends on: - {#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}
{#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}	This trigger uses temperature sensor values as well as temperature sensor status if available	`{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}>{$TEMP_CRIT:""}` Recovery expression: `{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].max(5m)}<{$TEMP_CRIT:""}-3`	HIGH
{#SENSOR_DESCR}: Temperature is too low: <{$TEMP_CRIT_LOW:""}	-	`{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}<{$TEMP_CRIT_LOW:""}` Recovery expression: `{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].min(5m)}>{$TEMP_CRIT_LOW:""}+3`	AVERAGE

This trigger uses temperature sensor values as well as temperature sensor status if available

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}>{$TEMP_WARN:""}

Recovery expression:

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].max(5m)}<{$TEMP_WARN:""}-3

WARNING

Depends on:

- {#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}

{#SENSOR_DESCR}: Temperature is above critical threshold: >{$TEMP_CRIT:""}

This trigger uses temperature sensor values as well as temperature sensor status if available

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}>{$TEMP_CRIT:""}

Recovery expression:

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].max(5m)}<{$TEMP_CRIT:""}-3

HIGH

{#SENSOR_DESCR}: Temperature is too low: <{$TEMP_CRIT_LOW:""}

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].avg(5m)}<{$TEMP_CRIT_LOW:""}

Recovery expression:

{TEMPLATE_NAME:sensor.temp.value[sensorReading.{#SNMPINDEX}].min(5m)}>{$TEMP_CRIT_LOW:""}+3

AVERAGE

Feedback

Please report any issues with the template at https://support.zabbix.com

Link	Source	Compatibility	Type, Technology	Created Updated
Template IPMI SuperMicro template_zabbix_2.2_ipmi_supermicro_5017a-ef_(and_other_atom_cpu)	GitHub Community Templates	5.0+
IPMI SuperMicro X9DRD-7LN4F template_supermicro_x9drd-7ln4f	GitHub Community Templates	5.0+
Supermicro SNMP Superdoctor 5 LLD Monitor Supermicro servers by snmp vs SuperDoctor5 (SD5).Monitored items:Fans (RPM)Physical disks (by hba or LSI raid card (see SD5 documentation)). By default deactivated.modelserial number (trigger exists)smart status (trigger exists)Power Supply (ok or not, trigger exists)Temperatures (celsius, trigger ... template_supermicro_snmp_superdoctor_5_lld	GitHub Community Templates	5.0+
Template IPMI Supermicro A1SAM-2750F template_supermicro_a1sam-2750f_(ipmi)	GitHub Community Templates	5.0+
IPMI - Supermicro - X10DRW-E Template for the X10DRW-E motherboard which includes:Applications (4):Fans - 6 itemsPower Supply - 2 itemsTemperature - 23 itemsVoltage - 13 itemsItems (46):Fan 1 - FansFan 2 - FansFan 3 - FansFan 4 - FansFan A - FansFan B - FansPS1 Status - Power SupplyPS2 Status - Power SupplyCPU1 - TemperatureCPU2 ... template_ipmi-supermicro-x10drw-e	GitHub Community Templates	5.0+
IPMI Supermicro X9SRI-F Template for IPMI SuperMicro X9SRI Motherboard (items, triggers, graphs). template_ipmi_supermicro_x9sri	GitHub Community Templates	5.0+
Template IPMI Supermicro X9DRL-7F-BO template_ipmi_supermicro_x9scl-f-b	GitHub Community Templates	5.0+
IPMI Supermicro X9SCLX9SCM IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan, Temperature, Voltage] template_ipmi_supermicro_x9scl_x9scm	GitHub Community Templates	5.0+
IPMI Supermicro X9DRT IPMI Supermicro X9DRTMeasuring all available values by IPMI.All are triggered.Plus some graphs. template_ipmi_supermicro_x9drt	GitHub Community Templates	5.0+
Template IPMI Supermicro X9DRL-7F-BO template_ipmi_supermicro_x9drl-7f-bo	GitHub Community Templates	5.0+
IPMI Supermicro X9DBL IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan, Temperature, Voltage]Items 30, Triggers 90, Graphs 3 template_ipmi_supermicro_x9dbl-if	GitHub Community Templates	5.0+
Template IPMI Supermicro X8DTL-3F template_ipmi_supermicro_x8dtl-3f	GitHub Community Templates	5.0+
IPMI Supermicro X10SRM-TF IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan Speed, Temperature, Voltage]Items 30, Triggers 12, Graphs 3 template_ipmi_supermicro_x10srm-tf	GitHub Community Templates	5.0+
IPMI Supermicro X10SRL-F IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan, Temperature, Voltage] template_ipmi_supermicro_x10srl-f	GitHub Community Templates	5.0+
IPMI Supermicro X10SLL-F template_ipmi_supermicro_x10sll-f	GitHub Community Templates	5.0+
IPMI SuperMicro X10DRT-H template_ipmi_supermicro_x10drt-h	GitHub Community Templates	5.0+
IPMI Supermicro SYS-6028R-TR IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan, Temperature, Voltage] template_ipmi_supermicro_sys-6028r-tr	GitHub Community Templates	5.0+
IPMI Supermicro SYS-5019S-L template_ipmi_supermicro_sys-5019s-l	GitHub Community Templates	5.0+
IPMI Supermicro SYS-5018D IPMI HW status [Fan, Temperature, Voltage], Triggers [Fan, Temperature, Voltage], Graphs [Fan, Temperature, Voltage] template_ipmi_supermicro_sys-5018d-mtf	GitHub Community Templates	5.0+
IPMI Supermicro H8DGT IPMI HW status [Fan, Temperature, Voltage, PS], Triggers [Fan, Temperature, Voltage, PS] template_ipmi_supermicro_h8dgt	GitHub Community Templates	5.0+
A simple template to poll sensordata for Supermicro X10SLL-F mainboards via IPMI github.com/JanKoppe/zabbix-supermicro-x10sll-f	GitHub 3		Template ipmi	2016-04-07 5 y

See all Zabbix community templates

观看Zabbix demo 视频

Get Zabbix Cloud today

Get Zabbix Cloud today

Get Zabbix Cloud today

Get Zabbix Cloud today

Zabbix + Supermicro

Supermicro

Available solutions

Supermicro Aten by SNMP

Overview

Requirements

Tested versions

Configuration

Setup

Macros used

Items

Triggers

LLD rule Temperature Discovery

Item prototypes for Temperature Discovery

Trigger prototypes for Temperature Discovery

LLD rule FAN Discovery

Item prototypes for FAN Discovery

Feedback

Supermicro Aten by SNMP

Overview

Requirements

Tested versions

Configuration

Setup

Macros used

Items

Triggers

LLD rule Temperature Discovery

Item prototypes for Temperature Discovery

Trigger prototypes for Temperature Discovery

LLD rule FAN Discovery

Item prototypes for FAN Discovery

Feedback

Supermicro Aten by SNMP

Overview

Setup

Zabbix configuration

Macros used

Template links

Discovery rules

Items collected

Triggers

Feedback

Supermicro Aten by SNMP

Overview

Requirements

Tested versions

Configuration

Setup

Macros used

Items

Triggers

LLD rule Temperature Discovery

Item prototypes for Temperature Discovery

Trigger prototypes for Temperature Discovery

LLD rule FAN Discovery

Item prototypes for FAN Discovery

Feedback

Supermicro Aten SNMP

Overview

Setup

Zabbix configuration

Macros used

Template links

Discovery rules

Items collected

Triggers

Feedback

Template Server Supermicro Aten SNMP

Overview

Setup

Zabbix configuration

Macros used

Template links

Discovery rules