Randomly proxy stops collecting data from SNMPv3 hosts

[asindona65]

Hi guys
I'm experiencing the following problem. I have a Zabbix 7.0.10 instance configured with several proxies, one for each customer (7.0.8 and 7.0.9 version for proxies, 7.0.9 for the proxy where there is the issue). Recently I started to monitor new hosts with SNMPv3 and after configuration...

[Vinodh4181]

I have created /22 subnet network discovery with systemname oid along with SNMP v3 creds (creds are same for both switches and routers).
In that subnet I have 66 aruba switches and 54 versa routers. After enabling discovery rule and actions I have discovered all 66 switches in 1hr but no router...

[andrey.ivanov]

Привет! Есть у кого шаблон для принтера

HP LaserJet MFP M426fdn

Хочу сделать мониторинг его в заббиксе, не могу нигде найти нормальный шаблон

[balaji]

I recently installed and configured my zabbix server to receive trap messages, It was working fine for v2 based machines. When I tried to configure to get v3 based trap using the Zabbix documentation, I am unable to see the trip message from the host. But when I tried to check from my local host using...

[justIT]

Hello I recently enabled SNMPv3 on a Sonicwall firewall, entered the credentials into zabbix, and read data off host items. The problem is that my items are set to pull snmp data every minute (which works great over SNMPv2), but most items only get data at a rate of every 5-10 minutes. Thanks an any...

[den_echte_jerre]

Hi all,
I have this issue gathering SNMPv3 data from 2 Cambium V1000 devices. I use Zabbix 6.4.18
When both hosts are added to Zabbix, only 1 is receiving data. When the Zabbix server is restarted, it could be that host A is receiving data and host B not, or sometimes the other way arou...

[lavis_cannon]

I've been struggling to get the auto discovery process in Zabbix v7 to create SNMPv3 interfaces on my MikroTik devices.

SNMP Walk functions with the same OIDs from the Zabbix VM:

AzureAdmin@node1-c-zabbix01-dev01:~$ snmpwalk -v3 -l authPriv -u ***** -a SHA -A ***** -x AES -X...

[kazzur]

I have 2 zabbix servers
test- this is an appliance base on almalinux 8 (downloaded from zabbix site)
prod - base on the rockylinux 9
Both servers are 6.4.14
On the test server I monitor printers using the snmp protocol. I export the templates and settings of these printers to...

[captain118]

I'm running Zabbix 6.0.24. I am trying to add my Cisco Catalist 9300 to be monitored using SNMPv3. Any suggestions would be great!
I do have snmpwalk working from the Zabbix Server. snmpwalk works using SHA and AES-256-C. However setting those values in the Zabbix UI does not allow the SNMP interface...

[dBruno]

Hello,

I’m trying to monitor two ILO5s with SNMP V3 using SHA256 and AES128.
I have Zabbix 7.0.0 compiled with OpenSSL 3.0.7 on a Rocky Linux 9 server. I’ve also tried it with Debian 11.

Monitoring ILO5 with SNMP V1 and V2 works fine, but with SNMP V3, I get an “Unsupported...

[emrecck]

Hi Team,

I need your help with the Huawei S5700 series switch monitoring with SNMPv3. I add my Huawei S5700 series device with SNMPv3 on Zabbix. Meanwhile, I am using the Huawei template downloaded from the Zabbix template page and I tried more than one template at different times. The...

[TzS2fg]

Hello,

i am trying to add cisco isr 4331 to Zabbix, using SNMPv3, but cant seem to make it work... btw SNMPv2 works fine.

for privacy reasons some settings will have "XXXXXX" in them.. i have double triple checked them and configured it as it is said in this post....

[GetMeSomeCoffee]

Hello everyone,
I'm currently struggling with getting SNMPv3 traps to work.
The deployment is completly dockerized and version 6.0.14 for the server-container and the snmp-container.
SNMP traps v1 are working fine but v3 are not registered at all. v3 is running with authentication...

[jpart]

Hello,

I have just recently started to tryout Zabbix monitoring software. Servers and other clients with agent are working fine but I'm having
trouble with SNMP and Brother printers.

Here is how I configured the Discovery Rule for testing purposes. I'm not very familiar...

[DigitalHayz]

So I recently decided to update our Cisco equipment to use SNMPv3 and as part of this project I am also integrating Zabbix into our environment. I have added a handful of devices and have been editing the built in Cisco IOS SNMP Template with the proper OIDs to make them work with each device. However,...