Brocade

Brocade Communications Systems, Inc. (subsidiary of Broadcom Inc.) is specializing in data and storage networking products, including routers and network switches for data center, campus and carrier environments, IP and Fibre Channel storage network fabrics, Network Functions Virtualization (NFV), software-defined networking (SDN), network management software.

Available solutions




This template is for Zabbix version: 6.2
Also available for: 6.0 5.4 5.0

Source: https://git.zabbix.com/projects/ZBX/repos/zabbix/browse/templates/net/brocade_fc_sw_snmp?at=release/6.2

Brocade FC SNMP

Overview

For Zabbix version: 6.2 and higher
https://community.brocade.com/dtscp75322/attachments/dtscp75322/fibre/25235/1/FOS_MIB_Reference_v740.pdf

This template was tested on:

  • Brocade 6520, version v7.4.1c
  • Brocade 300, version v7.0.0c
  • Brocade BL 5480, version v6.3.1c

Setup

Refer to the vendor documentation.

Zabbix configuration

No specific Zabbix configuration is required.

Macros used

Name Description Default
{$CPU.UTIL.CRIT}

-

90
{$FAN_CRIT_STATUS}

-

2
{$FAN_OK_STATUS}

-

4
{$HEALTH_CRIT_STATUS}

-

4
{$HEALTH_WARN_STATUS:"offline"}

-

2
{$HEALTH_WARN_STATUS:"testing"}

-

3
{$ICMP_LOSS_WARN}

-

20
{$ICMP_RESPONSE_TIME_WARN}

-

0.15
{$IF.ERRORS.WARN}

-

2
{$IF.UTIL.MAX}

-

90
{$IFCONTROL}

-

1
{$MEMORY.UTIL.MAX}

-

90
{$NET.IF.IFADMINSTATUS.MATCHES}

Ignore notPresent(6)

^.*
{$NET.IF.IFADMINSTATUS.NOT_MATCHES}

Ignore down(2) administrative status

^2$
{$NET.IF.IFALIAS.MATCHES}

-

.*
{$NET.IF.IFALIAS.NOT_MATCHES}

-

CHANGE_IF_NEEDED
{$NET.IF.IFDESCR.MATCHES}

-

.*
{$NET.IF.IFDESCR.NOT_MATCHES}

-

CHANGE_IF_NEEDED
{$NET.IF.IFNAME.MATCHES}

-

^.*$
{$NET.IF.IFNAME.NOT_MATCHES}

Filter out loopbacks, nulls, docker veth links and docker0 bridge by default

(^Software Loopback Interface|^NULL[0-9.]*$|^[Ll]o[0-9.]*$|^[Ss]ystem$|^Nu[0-9.]*$|^veth[0-9a-z]+$|docker[0-9]+|br-[a-z0-9]{12})
{$NET.IF.IFOPERSTATUS.MATCHES}

-

^.*$
{$NET.IF.IFOPERSTATUS.NOT_MATCHES}

Ignore notPresent(6)

^6$
{$NET.IF.IFTYPE.MATCHES}

-

.*
{$NET.IF.IFTYPE.NOT_MATCHES}

-

CHANGE_IF_NEEDED
{$PSU_CRIT_STATUS}

-

2
{$PSU_OK_STATUS}

-

4
{$SNMP.TIMEOUT}

-

5m
{$TEMP_CRIT_LOW}

-

5
{$TEMP_CRIT}

-

75
{$TEMP_WARN_STATUS}

-

5
{$TEMP_WARN}

-

65

Template links

There are no template links in this template.

Discovery rules

Name Description Type Key and additional info
FAN Discovery

-

SNMP fan.discovery

Filter:

AND_OR

- {#SENSOR_TYPE} MATCHES_REGEX 2

Network interfaces discovery

Discovering interfaces from IF-MIB.

SNMP net.if.discovery

Filter:

AND

- {#IFADMINSTATUS} MATCHES_REGEX {$NET.IF.IFADMINSTATUS.MATCHES}

- {#IFADMINSTATUS} NOT_MATCHES_REGEX {$NET.IF.IFADMINSTATUS.NOT_MATCHES}

- {#IFOPERSTATUS} MATCHES_REGEX {$NET.IF.IFOPERSTATUS.MATCHES}

- {#IFOPERSTATUS} NOT_MATCHES_REGEX {$NET.IF.IFOPERSTATUS.NOT_MATCHES}

- {#IFNAME} MATCHES_REGEX {$NET.IF.IFNAME.MATCHES}

- {#IFNAME} NOT_MATCHES_REGEX {$NET.IF.IFNAME.NOT_MATCHES}

- {#IFDESCR} MATCHES_REGEX {$NET.IF.IFDESCR.MATCHES}

- {#IFDESCR} NOT_MATCHES_REGEX {$NET.IF.IFDESCR.NOT_MATCHES}

- {#IFALIAS} MATCHES_REGEX {$NET.IF.IFALIAS.MATCHES}

- {#IFALIAS} NOT_MATCHES_REGEX {$NET.IF.IFALIAS.NOT_MATCHES}

- {#IFTYPE} MATCHES_REGEX {$NET.IF.IFTYPE.MATCHES}

- {#IFTYPE} NOT_MATCHES_REGEX {$NET.IF.IFTYPE.NOT_MATCHES}

PSU Discovery

-

SNMP psu.discovery

Filter:

AND_OR

- {#SENSOR_TYPE} MATCHES_REGEX 3

Temperature Discovery

-

SNMP temperature.discovery

Filter:

AND_OR

- {#SENSOR_TYPE} MATCHES_REGEX 1

Items collected

Group Name Description Type Key and additional info
CPU CPU utilization

MIB: SW-MIB

System's CPU usage.

SNMP system.cpu.util[swCpuUsage.0]
Fans {#SENSOR_INFO}: Fan status

MIB: SW-MIB

SNMP sensor.fan.status[swSensorStatus.{#SNMPINDEX}]
Fans {#SENSOR_INFO}: Fan speed

MIB: SW-MIB

The current value (reading) of the sensor.

The value, -2147483648, represents an unknown quantity.

The fan value will be in RPM(revolution per minute)

SNMP sensor.fan.speed[swSensorValue.{#SNMPINDEX}]
General SNMP traps (fallback)

The item is used to collect all SNMP traps unmatched by other snmptrap items

SNMP_TRAP snmptrap.fallback
General System location

MIB: SNMPv2-MIB

The physical location of this node (e.g., telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.</p> |SNMP |system.location[sysLocation.0]<p>**Preprocessing**:</p><p>- DISCARD_UNCHANGED_HEARTBEAT:12h`

General System contact details

MIB: SNMPv2-MIB

The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.

SNMP system.contact[sysContact.0]

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 12h

General System object ID

MIB: SNMPv2-MIB

The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determiningwhat kind of box' is being managed. For example, if vendorFlintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its Fred Router'.</p> |SNMP |system.objectid[sysObjectID.0]<p>**Preprocessing**:</p><p>- DISCARD_UNCHANGED_HEARTBEAT:12h`

General System name

MIB: SNMPv2-MIB

An administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.

SNMP system.name

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 12h

General System description

MIB: SNMPv2-MIB

A textual description of the entity. This value should

include the full name and version identification of the system's hardware type, software operating-system, and

networking software.

SNMP system.descr[sysDescr.0]

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 12h

Inventory Hardware serial number

MIB: SW-MIB

SNMP system.hw.serialnumber

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1d

Inventory Firmware version

MIB: SW-MIB

SNMP system.hw.firmware

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1d

Memory Memory utilization

MIB: SW-MIB

Memory utilization in %.

SNMP vm.memory.util[swMemUsage.0]
Network interfaces Interface {#IFNAME}({#IFALIAS}): Operational status

MIB: IF-MIB

The current operational state of the interface.

- The testing(3) state indicates that no operational packet scan be passed

- If ifAdminStatus is down(2) then ifOperStatus should be down(2)

- If ifAdminStatus is changed to up(1) then ifOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic

- It should change todormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incoming connection)

- It should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state

- It should remain in the notPresent(6) state if the interface has missing(typically, hardware) components.

SNMP net.if.status[ifOperStatus.{#SNMPINDEX}]
Network interfaces Interface {#IFNAME}({#IFALIAS}): Bits received

MIB: IF-MIB

The total number of octets received on the interface, including framing characters. This object is a 64-bit version of ifInOctets. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.in[ifHCInOctets.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

- MULTIPLIER: 8

Network interfaces Interface {#IFNAME}({#IFALIAS}): Bits sent

MIB: IF-MIB

The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit version of ifOutOctets.Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.out[ifHCOutOctets.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

- MULTIPLIER: 8

Network interfaces Interface {#IFNAME}({#IFALIAS}): Inbound packets with errors

MIB: IF-MIB

For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.in.errors[ifInErrors.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

Network interfaces Interface {#IFNAME}({#IFALIAS}): Outbound packets with errors

MIB: IF-MIB

For packet-oriented interfaces, the number of outbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of outbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.out.errors[ifOutErrors.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

Network interfaces Interface {#IFNAME}({#IFALIAS}): Outbound packets discarded

MIB: IF-MIB

The number of outbound packets which were chosen to be discarded

even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

One possible reason for discarding such a packet could be to free up buffer space.

Discontinuities in the value of this counter can occur at re-initialization of the management system,

and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.out.discards[ifOutDiscards.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

Network interfaces Interface {#IFNAME}({#IFALIAS}): Inbound packets discarded

MIB: IF-MIB

The number of inbound packets which were chosen to be discarded

even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

One possible reason for discarding such a packet could be to free up buffer space.

Discontinuities in the value of this counter can occur at re-initialization of the management system,

and at other times as indicated by the value of ifCounterDiscontinuityTime.

SNMP net.if.in.discards[ifInDiscards.{#SNMPINDEX}]

Preprocessing:

- CHANGE_PER_SECOND

Network interfaces Interface {#IFNAME}({#IFALIAS}): Interface type

MIB: IF-MIB

The type of interface.

Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA),

through updating the syntax of the IANAifType textual convention.

SNMP net.if.type[ifType.{#SNMPINDEX}]

Preprocessing:

- DISCARD_UNCHANGED_HEARTBEAT: 1d

Network interfaces Interface {#IFNAME}({#IFALIAS}): Speed

MIB: IF-MIB

An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of n' then the speed of the interface is somewhere in the range ofn-500,000' ton+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.</p> |SNMP |net.if.speed[ifHighSpeed.{#SNMPINDEX}]<p>**Preprocessing**:</p><p>- MULTIPLIER:1000000</p><p>- DISCARD_UNCHANGED_HEARTBEAT:1h`

Power supply {#SENSOR_INFO}: Power supply status

MIB: SW-MIB

SNMP sensor.psu.status[swSensorStatus.{#SNMPINDEX}]
Status Overall system health status

MIB: SW-MIB

The current operational status of the switch.The states are as follow:

online(1) means the switch is accessible by an external Fibre Channel port

offline(2) means the switch is not accessible

testing(3) means the switch is in a built-in test mode and is not accessible by an external Fibre Channel port

faulty(4) means the switch is not operational.

SNMP system.status[swOperStatus.0]
Status Uptime

MIB: SNMPv2-MIB

The time (in hundredths of a second) since the network management portion of the system was last re-initialized.

SNMP system.uptime[sysUpTime.0]

Preprocessing:

- MULTIPLIER: 0.01

Status SNMP agent availability

Availability of SNMP checks on the host. The value of this item corresponds to availability icons in the host list.

Possible value:

0 - not available

1 - available

2 - unknown

INTERNAL zabbix[host,snmp,available]
Status ICMP ping

-

SIMPLE icmpping
Status ICMP loss

-

SIMPLE icmppingloss
Status ICMP response time

-

SIMPLE icmppingsec
Temperature {#SENSOR_INFO}: Temperature

MIB: SW-MIB

Temperature readings of testpoint: {#SENSOR_INFO}

SNMP sensor.temp.value[swSensorValue.{#SNMPINDEX}]
Temperature {#SENSOR_INFO}: Temperature status

MIB: SW-MIB

Temperature status of testpoint: {#SENSOR_INFO}

SNMP sensor.temp.status[swSensorStatus.{#SNMPINDEX}]

Triggers

Name Description Expression Severity Dependencies and additional info
High CPU utilization

CPU utilization is too high. The system might be slow to respond.

min(/Brocade FC SNMP/system.cpu.util[swCpuUsage.0],5m)>{$CPU.UTIL.CRIT} WARNING
{#SENSOR_INFO}: Fan is in critical state

Please check the fan unit

count(/Brocade FC SNMP/sensor.fan.status[swSensorStatus.{#SNMPINDEX}],#1,"eq","{$FAN_CRIT_STATUS}")=1 AVERAGE
{#SENSOR_INFO}: Fan is not in normal state

Please check the fan unit

count(/Brocade FC SNMP/sensor.fan.status[swSensorStatus.{#SNMPINDEX}],#1,"ne","{$FAN_OK_STATUS}")=1 INFO

Depends on:

- {#SENSOR_INFO}: Fan is in critical state

System name has changed

System name has changed. Ack to close.

last(/Brocade FC SNMP/system.name,#1)<>last(/Brocade FC SNMP/system.name,#2) and length(last(/Brocade FC SNMP/system.name))>0 INFO

Manual close: YES

Device has been replaced

Device serial number has changed. Ack to close

last(/Brocade FC SNMP/system.hw.serialnumber,#1)<>last(/Brocade FC SNMP/system.hw.serialnumber,#2) and length(last(/Brocade FC SNMP/system.hw.serialnumber))>0 INFO

Manual close: YES

Firmware has changed

Firmware version has changed. Ack to close

last(/Brocade FC SNMP/system.hw.firmware,#1)<>last(/Brocade FC SNMP/system.hw.firmware,#2) and length(last(/Brocade FC SNMP/system.hw.firmware))>0 INFO

Manual close: YES

High memory utilization

The system is running out of free memory.

min(/Brocade FC SNMP/vm.memory.util[swMemUsage.0],5m)>{$MEMORY.UTIL.MAX} AVERAGE
Interface {#IFNAME}({#IFALIAS}): Link down

This trigger expression works as follows:

1. Can be triggered if operations status is down.

2. {$IFCONTROL:"{#IFNAME}"}=1 - user can redefine Context macro to value - 0. That marks this interface as not important. No new trigger will be fired if this interface is down.

3. {TEMPLATE_NAME:METRIC.diff()}=1) - trigger fires only if operational status was up(1) sometime before. (So, do not fire 'ethernal off' interfaces.)

WARNING: if closed manually - won't fire again on next poll, because of .diff.

{$IFCONTROL:"{#IFNAME}"}=1 and last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}])=2 and (last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}],#1)<>last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}],#2))

Recovery expression:

last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}])<>2 or {$IFCONTROL:"{#IFNAME}"}=0
AVERAGE

Manual close: YES

Interface {#IFNAME}({#IFALIAS}): High bandwidth usage

The network interface utilization is close to its estimated maximum bandwidth.

(avg(/Brocade FC SNMP/net.if.in[ifHCInOctets.{#SNMPINDEX}],15m)>({$IF.UTIL.MAX:"{#IFNAME}"}/100)*last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}]) or avg(/Brocade FC SNMP/net.if.out[ifHCOutOctets.{#SNMPINDEX}],15m)>({$IF.UTIL.MAX:"{#IFNAME}"}/100)*last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])) and last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])>0

Recovery expression:

avg(/Brocade FC SNMP/net.if.in[ifHCInOctets.{#SNMPINDEX}],15m)<(({$IF.UTIL.MAX:"{#IFNAME}"}-3)/100)*last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}]) and avg(/Brocade FC SNMP/net.if.out[ifHCOutOctets.{#SNMPINDEX}],15m)<(({$IF.UTIL.MAX:"{#IFNAME}"}-3)/100)*last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])
WARNING

Manual close: YES

Depends on:

- Interface {#IFNAME}({#IFALIAS}): Link down

Interface {#IFNAME}({#IFALIAS}): High error rate

Recovers when below 80% of {$IF.ERRORS.WARN:"{#IFNAME}"} threshold

min(/Brocade FC SNMP/net.if.in.errors[ifInErrors.{#SNMPINDEX}],5m)>{$IF.ERRORS.WARN:"{#IFNAME}"} or min(/Brocade FC SNMP/net.if.out.errors[ifOutErrors.{#SNMPINDEX}],5m)>{$IF.ERRORS.WARN:"{#IFNAME}"}

Recovery expression:

max(/Brocade FC SNMP/net.if.in.errors[ifInErrors.{#SNMPINDEX}],5m)<{$IF.ERRORS.WARN:"{#IFNAME}"}*0.8 and max(/Brocade FC SNMP/net.if.out.errors[ifOutErrors.{#SNMPINDEX}],5m)<{$IF.ERRORS.WARN:"{#IFNAME}"}*0.8
WARNING

Manual close: YES

Depends on:

- Interface {#IFNAME}({#IFALIAS}): Link down

Interface {#IFNAME}({#IFALIAS}): Ethernet has changed to lower speed than it was before

This Ethernet connection has transitioned down from its known maximum speed. This might be a sign of autonegotiation issues. Ack to close.

change(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])<0 and last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])>0 and ( last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=6 or last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=7 or last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=11 or last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=62 or last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=69 or last(/Brocade FC SNMP/net.if.type[ifType.{#SNMPINDEX}])=117 ) and (last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}])<>2)

Recovery expression:

(change(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}])>0 and last(/Brocade FC SNMP/net.if.speed[ifHighSpeed.{#SNMPINDEX}],#2)>0) or (last(/Brocade FC SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}])=2)
INFO

Manual close: YES

Depends on:

- Interface {#IFNAME}({#IFALIAS}): Link down

{#SENSOR_INFO}: Power supply is in critical state

Please check the power supply unit for errors

count(/Brocade FC SNMP/sensor.psu.status[swSensorStatus.{#SNMPINDEX}],#1,"eq","{$PSU_CRIT_STATUS}")=1 AVERAGE
{#SENSOR_INFO}: Power supply is not in normal state

Please check the power supply unit for errors

count(/Brocade FC SNMP/sensor.psu.status[swSensorStatus.{#SNMPINDEX}],#1,"ne","{$PSU_OK_STATUS}")=1 INFO

Depends on:

- {#SENSOR_INFO}: Power supply is in critical state

System status is in critical state

Please check the device for errors

count(/Brocade FC SNMP/system.status[swOperStatus.0],#1,"eq","{$HEALTH_CRIT_STATUS}")=1 HIGH
System status is in warning state

Please check the device for warnings

count(/Brocade FC SNMP/system.status[swOperStatus.0],#1,"eq","{$HEALTH_WARN_STATUS:\"offline\"}")=1 or count(/Brocade FC SNMP/system.status[swOperStatus.0],#1,"eq","{$HEALTH_WARN_STATUS:\"testing\"}")=1 WARNING

Depends on:

- System status is in critical state

has been restarted

Uptime is less than 10 minutes.

last(/Brocade FC SNMP/system.uptime[sysUpTime.0])<10m WARNING

Manual close: YES

Depends on:

- No SNMP data collection

No SNMP data collection

SNMP is not available for polling. Please check device connectivity and SNMP settings.

max(/Brocade FC SNMP/zabbix[host,snmp,available],{$SNMP.TIMEOUT})=0 WARNING

Depends on:

- Unavailable by ICMP ping

Unavailable by ICMP ping

Last three attempts returned timeout. Please check device connectivity.

max(/Brocade FC SNMP/icmpping,#3)=0 HIGH
High ICMP ping loss

-

min(/Brocade FC SNMP/icmppingloss,5m)>{$ICMP_LOSS_WARN} and min(/Brocade FC SNMP/icmppingloss,5m)<100 WARNING

Depends on:

- Unavailable by ICMP ping

High ICMP ping response time

-

avg(/Brocade FC SNMP/icmppingsec,5m)>{$ICMP_RESPONSE_TIME_WARN} WARNING

Depends on:

- High ICMP ping loss

- Unavailable by ICMP ping

{#SENSOR_INFO}: Temperature is above warning threshold

This trigger uses temperature sensor values as well as temperature sensor status if available

avg(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)>{$TEMP_WARN:"{#SENSOR_INFO}"} or last(/Brocade FC SNMP/sensor.temp.status[swSensorStatus.{#SNMPINDEX}])={$TEMP_WARN_STATUS}

Recovery expression:

max(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)<{$TEMP_WARN:"{#SENSOR_INFO}"}-3
WARNING

Depends on:

- {#SENSOR_INFO}: Temperature is above critical threshold

{#SENSOR_INFO}: Temperature is above critical threshold

This trigger uses temperature sensor values as well as temperature sensor status if available

avg(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)>{$TEMP_CRIT:"{#SENSOR_INFO}"}

Recovery expression:

max(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)<{$TEMP_CRIT:"{#SENSOR_INFO}"}-3
HIGH
{#SENSOR_INFO}: Temperature is too low

-

avg(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)<{$TEMP_CRIT_LOW:"{#SENSOR_INFO}"}

Recovery expression:

min(/Brocade FC SNMP/sensor.temp.value[swSensorValue.{#SNMPINDEX}],5m)>{$TEMP_CRIT_LOW:"{#SENSOR_INFO}"}+3
AVERAGE

Feedback

Please report any issues with the template at https://support.zabbix.com

Known Issues

  • Description: no IF-MIB::ifAlias is available
    • Version: v6.3.1c, v7.0.0c, v7.4.1c
    • Device: all

Articles and documentation

+ Propose new article

Didn't find integration you need?